Red
Red

WALLPAPER > VERMICULE BP205001

Photo currently unavailable
colours
4 available colours
VERMICULE BP205001
Small plant foliage typical of Indian last process plates. Wallpaper hand-printed in a frame. Untrimmed.
Add to my selection
Composition :
100% Papier/100% paper. Raccord droit/Straight repeat. Vendu au rouleau/Sold per roll. Non émargé/Not trimmed.
Colour:
Antique red
Style:
18th century style, Indiennes
Type:
Small motifs

Technical information
Weight : 450 gr
Width: 71.12 cm / 28.00 inch
Type of repeat: Horizontal 11.00 cm / 4.00 inch, Vertical 9.00 cm / 3.00 inch
Length of the roll: 4.57 m / 5.00 yard
Matching products
This product matches with :
Products viewed
HANGING INSTRUCTIONS
Correct identification of surfaces and the appropriate preparation is critical to successful hanging.

It is the responsibility of the hanger to check individual site circumstances:
  • To correctly identify the surface onto which you are hanging and possibly organize a porosity test.
  • To determine the correct surface preparation for your site.
Surface preparation:
Differing designs will have various masking capabilities on surface imperfections. Therefore, plain and smooth designs will be less forgiving on poor and uneven wall surfaces.
All surfaces should be:
  • Clean - remove all surface contamination, e.g. dirt, grease and pigmented marks such as felt pen etc. Wash off using a detergent solution, rinse and allow to dry thoroughly.
  • Sound & Smooth - free of flaking paint and old wallpapers/backing. Evidence of previous adhesive should be removed with hot water. Brittle and uneven surfaces will require a remedial treatment.
  • If necessary, perform any surface repairs.
  • Uniform in color – in order to prevent transparency, equalize color (especially on lighter products) : Before hanging a dark wallcovering on a light surface, prepare the wall with a colored primer to hide the joints.
  • Treated for mould - treat with fungicidal if necessary and wash in accordance with pack instructions.
  • Dry in depth - in case of doubt, test with a moisture meter.
  • Normally absorbent – check porosity (the water drop test). Treat if necessary (scour, primer sealer…).
Similar surfaces can have differing absorption rates (e.g., with plaster, both the mix and application can affect absorption). Consequently, these recommendations can only be guidelines and may have to be adjusted for specific site circumstances.
TYPICAL ABSORBENT SURFACES
  • Uncoated plaster, Plasterboard, Wood
  • Most water based paints (matt)
  • Dry wall sealer (if correctly applied)
  • Primer sealer (if correctly applied)
N.B. Wooden surfaces may require specific preparation.
TYPICAL NON ABSORBENT SURFACES
  • Formica, Glassfibre, Metal
  • Most oil based paints (gloss, vinyl silk)
  • Dry wall sealer (if heavily applied or multicoats)
  • Primer sealer (if not diluted correctly)
N.B. Metal surfaces will require appropriate primers.
BEFORE YOU START:
Please ensure the following:
  • The wallcoverings are : conform to the order / conform as sample.
  • Before hanging, examine each roll to check for any faults. You should have sufficient material to complete the job in the same batch.
  • The batches of different rolls must be identical; never mix different batches on the same wall.
  • Use the correct adhesive for your individual site circumstances and the nature of the surface. Use a fixing agent if necessary.

  • Adequate site conditions must have :
    • good lighting for correct surface inspection
    • minimum ambient temperature of 10°C/50°F
    • good ventilation and clean working conditions

  • Avoid excessive ambient temperatures: radiators should ideally be removed before and 24 hours prior hanging. If this is not possible, they must be turned off and kept off until the wallcovering has fully dried.
  • Trial hang of 3 drops : inspect during and one hour after each drop.
CHOSING THE ADHESIVE
PRODUCTS WIDTH PIERRE FREY Collections Recommended adhesives for normally absorbent surfaces in moisture free rooms Paste the paper/wall
Paper sold by roll from 20”
to 36”
COLLECTIONS – Screen printing
BOUSSAC - FEROE
PIERRE FREY - CONFETTIS
Powder glue
type « METYLAN EXPERT »
or « METYLAN SPECIAL »

Paste the paper
Paper sold by roll from 20”
to 36”
BOUSSAC - POLKA
BRAQUENIE - ADELAÏDE
PIERRE FREY - JACARANDA
PIERRE FREY - RACINES
Powder glue type « METYLAN EXPERT »
or « METYLAN INTISSE »

Paste the wall
Nonwoven sold by yard Nonwoven backed fabric from 37”
to 60”
PIERRE FREY - JACARANDA
PIERRE FREY - LES DESSINS
PIERRE FREY - RACINES
Premixed glue
type « OVALIT TM »

Paste the wall
Vinyls from 20”
to 60”
Custom Orders Case by case -> contact us
Paste the wall

N.B. Adhesives contain fungicides to prevent against mould. Wash hands after use and keep away from children and animals.
HANGING INSTRUCTIONS
  1. Cut the drop – the length of the paper from top to bottom – keeping a 10 cm (4”) margin to each full length to allow for trimming.
  2. Depending on the product, paste the wall or the paper directly with the use of a roller.
  3. Start in a corner nearest to the main light source and plumb the first length. Always use rolls (when numbered) sequentially, hanging the highest number first. Always number the top of each drop as you cut it, in pencil on the back, to ensure a safe system of reversal or straight hanging.
  4. Adjust the drops edge-to-edge and delicately remove the air with a plastic smoothing spatula or a brush, from top to bottom and from the center outwards.
  5. Carefully wipe any excess paste with a damp sponge before it dries.
  6. Trim the margins with a cutter.
Trimmed wallcoverings: hang edge-to-edge respecting the design.

Untrimmed wallcoverings: after cutting the drops to the appropriate length (height of wall + margin), cut off with acutter on a table the unprinted white part of the paper, which will be laid over the last drop on the wall.

Trimmed wallcoverings: following the instructions of chosen adhesive and its support (paper or nonwoven), hangthe drop overlapping on the previous drop to match the design. When hanging stripes, make sure to hang equal width stripes.

Nonwoven backed fabrics: our nonwoven backed fabrics are trimmed to be hung edge-to-edge. Nonetheless, forperfectly invisible joints, they can also be hung by overlapping following the above instructions.
HANGING TIPS
  • Never dilute a ready-to-use adhesive (adhesive for wallcoverings in wide width).
  • Never fill over doors or under windows with off cuts. Join in corners using correct edge. Do not join a drop at the level of salient angles.
  • Avoid putting adhesive on the decorative side of the wallcovering. In case of any stains, clean immediately with a dry and clean cloth.
  • Allow material to settle for 10 - 15 minutes prior to trimming top and bottom.
  • Textile wallcoverings require careful storage (do not store on their edges, in a clean condition with delicate handling).
Inspect each drop as you hang it, and stop immediately if the result looks unacceptable.
No claims will be accepted for hanging charges or for consequential loss beyond 3 drops.

IN CASE OF DOUBT, STOP AND CONTACT US
Close

SHARE

your message has been sent
Close

HELP ADVANCED SEARCH

Check or uncheck the proposed filters. The selection of products is refined according to your choices.

For example, if you are looking for a Pierre Frey fabric with motifs, check the "Pierre Frey" advanced Search box,
then "Motifs".
The fabrics matching your request will then be displayed.
You can also choose a colour in certain product environments.
Close

AVAILABLE SHADES OF WOOD

wenge
walnut
Cherry
blond
Chestnut
white-leaded
black
Almond
Cherry-red
Yellow
reseda
Blue
grey
white
golden